Free Shipping on Orders Over $99  ·  No Code Needed

Borla 10-12 Ford F-150 Raptor 6.2L V8 2/4WD AT Touring SS Catback Exhaust

*Photo may not represent actual product

This Borla Touring cat-back is a 3-inch stainless system that splits into dual 2.5-inch pipes and ends in polished 4-inch T-304 tips. It is built for the 6.2L V8 in the 2010-2014 Ford F-150 SVT Raptor and the 2011-2012 Harley-Davidson Edition F-150. The manufacturer says the kit replaces the factory front resonator and uses its patented straight-through, multi-core muffler design to improve exhaust flow. Compared with stock, the main change is tone: the manufacturer describes a mellow Touring note with no cabin drone, which suits a daily-driven Raptor. Versus cheaper universal kits, buyers get CNC-bent tubing for a vehicle-specific fit, T-304 stainless in place of 409-grade alternatives, and the manufacturer's million-mile warranty.

Owners on user forums describe the volume as anywhere from a little louder than stock to noticeably deeper under throttle, so results depend on the rest of the exhaust setup. Search terms for this part include 2010-2014 Raptor 6.2 Touring catback, SVT Raptor 6.2L Borla 140404 no drone, and F-150 Raptor 6.2 cat-back bolt-on install. The system is a practical upgrade for a truck that already sees street use and keeps the factory exhaust layout.

  • Part Number: 140404
  • Fitment: 2010-2014 Ford F-150 SVT Raptor 6.2L V8 (2WD/4WD, automatic or manual); 2011-2012 Ford F-150 Harley-Davidson Edition 6.2L V8
  • System Type: Cat-back, replaces factory front muffler (resonator)
  • Pipe Diameter: 3" inlet into dual 2.5" outlets
  • Tip: 4" polished rolled angle-cut, truck side exit
  • Material: T-304 stainless steel
  • Sound Level: Touring (mellow, no drone)
  • Warranty: Million-mile warranty (per the manufacturer)

FAQ:

Does this kit replace the factory resonator?

The manufacturer states that this Touring system replaces the factory front muffler (resonator), so it is a full cat-back rather than a tailpipe-only upgrade.

Will it fit a 2011-2012 Harley-Davidson Edition F-150?

The manufacturer lists the 2011-2012 Harley-Davidson Edition F-150 with the 6.2L V8 as a fitment for this part. Owners on user forums reported that one Harley install needed a short length of 3-inch pipe to close a gap at the resonator, so check your fit before you order.

Will this exhaust cause drone on the highway?

The manufacturer describes the Touring tone as mellow with no drone inside the vehicle. Owners on user forums say it is a bit louder than stock with a deeper rumble under throttle, though not overly loud.

What should I watch for during installation?

Owners on user forums advise paying close attention to the O2 sensors. One owner reported that a sensor was dinged and cracked during removal, which later caused an emissions problem.

Installing it yourself

Owners on user forums describe this as a bolt-on job that a home garage can handle, but one owner working with a floor jack and stands found it slow because the pipes had to be turned and worked over the rear axle. Per the manufacturer's Ford F-150 Raptor installation guide, lubricate the hangers, rubber isolators, bolts and nuts first, leave clamps loose until the pipes are positioned, then check clearance and tip alignment before final tightening. One owner reported that a couple of clamps in the kit were the wrong size, so inventory the hardware before you start. Disconnect the O2 sensors carefully, since they are the most likely point of damage.

  • MPN: 140404
  • Manufactured by: Borla
  • Units per SKU: 1
  • In Stock: 4
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$2,199.99

MSRP / List price
Member Price
Your price after signing in
$2,199.99
Only 4 left in stock — order soon
Add to Cart:
MPN
140404
Manufacturer
Borla
Availability
Only 4 left
Ships Same Day
Order before 5pm PST and this product ships same day
Member Pricing
Easy Returns
Expert Support
Secure Checkout