Free Shipping on Orders Over $99  ·  No Code Needed

EBC 02 Cadillac Escalade 5.3 (Akebono rear caliper) GD Sport Front Rotors

*Photo may not represent actual product

The EBC GD7047 is a front-position rotor from the 3GD Series Sport line, listed for the 2002 Cadillac Escalade 5.3 with an Akebono rear caliper. The wide aperture slots draw cooling air beneath the pad under load, which helps brake temperatures drop. That cooling is the main reason to upgrade from a plain stock disc when you tow or make repeated hard stops. The rotor also uses dimples, and dimple drilling avoids stress cracks while giving the finish a sleek look and corrosion resistance.

Compared with a blank replacement, the GD design gives you a pad face that stays cleaner. Its slots protect the off-brake areas, such as the pad swept area and the inside of the hub, from rust. If you're searching for a 2002 Escalade 5.3 slotted dimpled front rotor for towing or spirited street driving, this is the set built for that duty. Confirm your front caliper and brake package before ordering, because the new rotors need to match your exact year, trim, drivetrain, and brake package. Replace the fronts as a pair so braking stays even side to side.

  • Product Line: EBC 3GD Series Sport Slotted Rotor
  • Position: Front (single axle)
  • Application: 2002 Cadillac Escalade 5.3 (Akebono rear caliper)
  • Rotor Design: Vented, wide-aperture slotted and dimpled
  • Finish: Black thermic anti-corrosion coating
  • Material: Grey iron casting
  • Bolt Pattern: 6-lug
  • Pad Reference: FMSI D785

FAQ:

Do I need to strip the black coating before installing these rotors?

No. EBC's fitting instructions say the coating on grooved rotors wears off during the first 100 miles of braking, and it should not be removed at installation. The manufacturer also states that using brake cleaner or other methods to strip the coating is not covered under EBC's warranty.

Should I replace just the driver or passenger side rotor?

The manufacturer says rotors should be replaced in pairs. The manufacturer's instructions state to always replace the rotors in pairs.

How long should I break in the pads and rotors?

Guidance varies between EBC's documents. One EBC fitting sheet calls for gentle use for the first 100 miles until optimum braking is observed. Another EBC-branded install sheet allows 300 miles of urban driving for pads and rotors to bed in. Confirm the current bedding procedure with the manufacturer before your first long drive.

Installing it yourself

This is a moderate-difficulty front brake job that most home mechanics with a good jack and jack stands can handle. Typical tools include a floor jack, jack stands, a lug wrench or impact, a breaker bar, a torque wrench, a C-clamp or piston compression tool, a dead-blow mallet, and a wire brush. Before fitting, the wheel mounting flange must be cleaned, since rust or scale causes runout and brake judder. Check runout with a dial indicator after mounting, and if it is out of spec, dismount the rotor and rotate it one bolt hole. A stuck rotor usually needs a rubber mallet or dead blow hammer to free it from the hub. Keep anti-seize off the rotor's friction surface. Do not let the caliper hang from its hose; do not unbolt the brake hose going to the caliper, because that lets air into the hydraulic system. Torque the lug nuts in a star pattern to the figure in the vehicle service information.

  • MPN: GD7047
  • Manufactured by: EBC
  • Units per SKU: 1
  • In Stock: 7
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$310.94

MSRP / List price
Member Price
Your price after signing in
$310.94
In Stock — ships same day if ordered before 5pm PST
Add to Cart:
MPN
GD7047
Manufacturer
EBC
Availability
In Stock (7)
Ships Same Day
Order before 5pm PST and this product ships same day
Member Pricing
Easy Returns
Expert Support
Secure Checkout