Free Shipping on Orders Over $99  ·  No Code Needed

Power Stop 92-98 Lexus SC300 Rear Z23 Evolution Sport Brake Kit

*Photo may not represent actual product

The Power Stop K1072 is a rear-axle Z23 Evolution Sport brake upgrade kit for the 1992-1998 Lexus SC300. It pairs drilled and slotted rear rotors with carbon-fiber reinforced ceramic pads, along with stainless-steel hardware, so you get a matched pad-and-rotor set rather than mismatched parts from separate lines. The manufacturer describes the compound as low-dust and fade-resistant, which makes it a practical step up from stock rear pads for daily driving and spirited back-road use. Searching for a 92-98 SC300 rear drilled rotor kit, carbon ceramic pads, or bolt-on SC300 rear brake upgrade? This kit targets that exact application. Owners on user forums report that 92-98 SC300 rear brakes share the same sizing, though 1998-2000 models reportedly use different rear calipers and rotors, so verify your year before ordering.

Installation is a bolt-on job for anyone comfortable with rear disc brake work, with no modifications required according to the manufacturer. Pads must be bedded in properly: the manufacturer recommends five moderate stops from 35 mph to 5 mph in quick succession, letting the brakes heat without cooling them with water, because proper bedding helps prevent rotor warping. Plan for a full brake fluid bleed after the caliper work, since user forums commonly describe pad swaps combined with bleeding as a cumbersome, multi-step process.

  • Fitment: 1992-1998 Lexus SC300 (rear axle)
  • Kit Contents: 2 rear drilled and slotted rotors, 1 rear carbon-fiber ceramic pad set, stainless-steel hardware
  • Pad Material: Carbon-fiber reinforced ceramic
  • Rotor Design: Cross-drilled and slotted
  • Dust Level: Low-dust formula
  • Lubricant Included: High-temp brake lubricant

FAQ:

Will this kit fit a 1999-2000 Lexus SC300?

This kit is listed for 1992-1998 SC300 models. Owners on user forums report that 1998-2000 SC300 rear calipers and rotors differ from earlier cars, so confirm fitment with the manufacturer using your VIN before ordering.

Do the new pads need a break-in procedure?

Yes. The manufacturer recommends five moderate stops from 35 mph to 5 mph without letting the brakes cool, followed by a cooling stage. Water should never be used to cool the brakes, and proper bedding helps prevent rotor warping.

Do the rear caliper pistons need special handling during pad replacement?

Owners on user forums say the most reliable method is to open the bleeder screw and push the piston back, which lets fluid escape rather than being forced back into the reservoir. Any time the bleeder is loosened, the system needs to be bled afterward.

Installing it yourself

This is a manageable weekend project for a home mechanic. You will need a floor jack, jack stands, wheel chocks, a C-clamp or piston-retraction tool, a brake bleeder wrench, fresh DOT brake fluid, and the included high-temp lubricant. Support the vehicle securely on stands and never let the caliper hang from the flexible brake hose. Check the rotor for runout before installing, since excessive runout can cause pulsation. Torque all fasteners to the manufacturer's specifications, bed the new pads using the break-in procedure, and finish by bleeding the rear brakes until clean fluid runs from the bleeder.

  • MPN: K1072
  • Manufactured by: PowerStop
  • Units per SKU: 1
  • In Stock: 1
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$143.39

MSRP / List price
Member Price
Your price after signing in
$143.39
Only 1 left in stock — order soon
Add to Cart:
MPN
K1072
Manufacturer
PowerStop
Availability
Only 1 left
Ships Same Day
Order before 5pm PST and this product ships same day
Member Pricing
Easy Returns
Expert Support
Secure Checkout