Free Shipping on Orders Over $99  ·  No Code Needed

Power Stop 18-21 Volvo XC60 Rear Z23 Evolution Brake Kit

*Photo may not represent actual product

PowerStop's Z23 Evolution rear kit for the 2018–2021 Volvo XC60 combines carbon-fiber ceramic brake pads, drilled and slotted rotors, and stainless-steel hardware into one bolt-on set for the rear axle. The manufacturer describes the kit as a daily-driver upgrade, and says its carbon-fiber ceramic formula is engineered to add stopping force while remaining comfortable in traffic. The drilled and slotted rotors are meant to help manage heat during repeated stops, and the zinc-plated rotor surface is intended to resist rust, which matters on a rear disc that sees limited use. Because the manufacturer engineers the pads and rotors as a matched kit, an XC60 owner gets a coordinated rear upgrade rather than piecing together mismatched parts.

Beyond stopping power, the kit addresses the everyday complaints that push owners to upgrade. The manufacturer says the carbon-fiber ceramic pads run a low-dust formula, which keeps rear wheels cleaner between washes. Dual-layer rubberized shims are designed to dampen vibration for quieter braking, and the included hi-temp brake lubricant and premium stainless-steel hardware support smooth caliper movement. Fitment is listed for the 2018–2021 XC60 rear axle, but trim coverage and rear rotor diameter vary across catalogs, so confirm your exact trim and VIN against the manufacturer's fitment guide before ordering. Searches for 2018-2021 Volvo XC60 rear brake kit, XC60 carbon ceramic rear pads, and drilled slotted rear rotors all match this kit. Plan a proper bed-in: the manufacturer recommends roughly five moderate stops from 35 mph to 5 mph in quick succession, followed by a cooling drive of about five minutes, and never cooling the brakes with water.

  • Axle Position: Rear
  • Vehicle Application: 2018–2021 Volvo XC60 (trim-dependent; verify fitment)
  • Pad Compound: Carbon-fiber ceramic (Z23 Evolution Sport)
  • Rotor Style: Drilled and slotted
  • Rotor Finish: Zinc plated
  • Pad Shims: Dual-layer rubberized
  • Hardware: Premium stainless-steel with pin bushing kit
  • Lubricant: Hi-temp brake lubricant included

FAQ:

Do the new pads and rotors need a break-in?

Yes. The manufacturer says a proper bed-in is critical to performance. It recommends about five moderate stops from 35 mph to 5 mph in rapid succession without letting the brakes cool, followed by a cooling drive of roughly five minutes at moderate speed. Avoid holding the pedal down at a stop while the rotors are hot, since that can imprint the rotor and contribute to brake judder.

Can I cool the rotors with water after installation?

No. The manufacturer advises never cooling the brakes with water, as this can damage them. Let the brakes return to normal operating temperature on their own.

What should I check if the brakes are noisy after installation?

The manufacturer notes that worn or damaged hardware can lead to noise or poor pad performance. Also keep brake lube off the friction side of the pads. Re-check the hardware and pad seating before assuming a pad defect.

Installing it yourself

Per the manufacturer's general brake-kit installation guide, gather the new pads, the brake fluid specified in your owner's manual, brake component lube, safety glasses, and gloves before you start. Check that the brake fluid reservoir sits about half full, and never let the caliper hang from the brake hose, since that can damage the hose. Clean any rust off the hub mating surface with a wire brush and hub cleaning kit. Thicker pads require pushing the caliper piston back into the caliper body, and the manufacturer warns that the rubber boot can extend the bolt and interfere during installation. Rotor runout can cause brake pulsation, so check it. Torque the caliper bolts to the Volvo specification from the service information, and bleed the system if fluid is released through the bleeder.

  • MPN: K8224
  • Manufactured by: PowerStop
  • Units per SKU: 1
  • In Stock: 1
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$163.15

MSRP / List price
Member Price
Your price after signing in
$163.15
Only 1 left in stock — order soon
Add to Cart:
MPN
K8224
Manufacturer
PowerStop
Availability
Only 1 left
Ships Same Day
Order before 5pm PST and this product ships same day
Member Pricing
Easy Returns
Expert Support
Secure Checkout