Free Shipping on Orders Over $99  ·  No Code Needed

Power Stop 2013 Infiniti JX35 Front Z17 Evolution Geomet Coated Brake Kit

*Photo may not represent actual product

The Power Stop CRK6496 is a front brake kit for the 2013 Infiniti JX35, built on the manufacturer's Z17 Evolution platform. The manufacturer describes it as Genuine Geomet coated rotors paired with Z17 Clean Ride ceramic pads, stainless-steel installation hardware, and high-temperature brake lubricant. The rotors are coated over their full surface, including inside the vanes, to fight rust and corrosion where it usually starts. The pads use a low-dust formula that the manufacturer says was validated through third-party on-vehicle testing in the USA. Buying rotors and pads separately means matching components yourself, so this kit is the simpler route to a coated, low-dust front brake refresh for a 2013 JX35 daily driver.

Confirm your VIN-specific fitment before ordering, because listings for this part number show year and model ranges that do not fully agree. Install is a standard pad-and-rotor job. The manufacturer's guide lists the tools needed, including a caliper piston compressor or C-clamp, jack stands, and wheel chocks, and estimates roughly five hours of labor. After installation, the manufacturer recommends a bedding sequence of repeated decelerations from 30 mph to 5 mph, with cooling pauses between each stop, to lay down an even pad transfer layer on the coated rotors. Searches for 2013 Infiniti JX35 front Geomet rotors, Z17 ceramic low-dust pads, and JX35 brake upgrade kit installation point to this exact setup.

  • Part Number (MPN): CRK6496
  • Position: Front axle
  • Application: 2013 Infiniti JX35 (confirm fitment by VIN)
  • Rotor Finish: Genuine Geomet coated, including inside the vanes
  • Pad Type: Z17 Clean Ride ceramic with dual-layer rubberized shims
  • Kit Contents: Front rotors, ceramic brake pads, stainless-steel hardware, high-temperature brake lubricant

FAQ:

Does the CRK6496 kit include everything needed for a front brake job?

The manufacturer states the kit includes the Geomet coated rotors, Z17 Clean Ride ceramic pads, stainless-steel installation hardware, and high-temperature brake lubricant, with sensors included where applicable to the vehicle.

What break-in procedure does the manufacturer recommend?

The manufacturer recommends 30 decelerations from 30 mph to 5 mph, with about 30 seconds of cooling between each stop. Expect a resin smell as the brakes heat up. If a stop is forced, complete it and avoid holding the pedal down on hot rotors, since that can imprint the pad onto the rotor.

Why are the rotors coated inside the vanes?

The manufacturer says full coverage, including inside the vanes, is intended to extend rotor life and protect against rust and corrosion in areas that are hard to inspect.

Installing it yourself

The manufacturer's install guide lists brake fluid as specified in the owner's manual, brake component lube, a caliper piston compressor or C-clamp, a jack and jack stands rated for the vehicle, and wheel chocks. The guide's steps cover removing the pads and caliper bracket, cleaning the rotor hub, installing the bracket and new pads, then mounting the wheel and lug nuts. Clean the hub thoroughly before fitting the new rotor, and do not hold the brake pedal down while the rotors are hot during the bedding procedure. Plan for a full afternoon if this is your first pad-and-rotor job.

  • MPN: CRK6496
  • Manufactured by: PowerStop
  • Units per SKU: 1
  • On Order: 1
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$223.96

MSRP / List price
Member Price
Your price after signing in
$223.96
Add to Cart:
MPN
CRK6496
Manufacturer
PowerStop
Availability
Out of Stock
Ships Within
1–2 Business Days
Member Pricing
Easy Returns
Expert Support
Secure Checkout