Free Shipping on Orders Over $99  ·  No Code Needed

Power Stop 20-25 Jeep Gladiator Front Z36 Coated Truck & Tow Brake Kit

*Photo may not represent actual product

This is the front-axle pad and rotor package from PowerStop's Z36 Truck & Tow line, built for Gladiator JT owners who tow, haul, or run larger tires. The pads are reinforced with carbon fiber for heavier loads, and the drilled and slotted rotors are meant to shed heat on long grades. Compared with a basic OE-style replacement, the case for the upgrade rests on fade resistance under load. One owner on a user forum ran 35s for the last 50,000 miles with the Power Stop rotors and pads on the front and said the stopping power was better than with the stock 33s. Because the pads and rotors are matched as one set, you also avoid mixing friction material from one brand with rotors from another, a point owners on user forums often raise.

The listing covers 2020–2025 Jeep Gladiator JT applications, so this is a practical choice for daily-driven trucks with moderate lift and tire upgrades. Searchers looking for Gladiator JT front brake pads and rotors, carbon-fiber ceramic pads for towing, or drilled and slotted rotors for 35-inch tires will find this kit relevant. Plan for a proper break-in: the manufacturer recommends five moderate stops from 35 mph to 5 mph in rapid succession without letting the brakes cool. Expect a resin smell during the first hot stops, which the manufacturer describes as normal.

  • Part Number: CPK7940-36
  • Axle Position: Front
  • Pad Material: Carbon-fiber ceramic (Z36 Truck & Tow)
  • Rotor Type: Drilled and slotted
  • Rotor Finish: Coated
  • Fitment: 2020–2025 Jeep Gladiator JT (confirm against your VIN and brake package)
  • Break-In: Five moderate stops from 35 mph to 5 mph, without cooling between stops

FAQ:

Do I need to break in these pads and rotors?

Yes. The manufacturer's break-in procedure calls for five moderate stops from 35 mph to 5 mph in quick succession without letting the brakes cool. The manufacturer also notes that a resin odor is expected as the brakes heat up.

Can I install only the pads and keep my stock rotors?

Owners on user forums advise against a pad-only swap and recommend fitting the new pads with fresh or turned rotors, since worn rotors can reduce the benefit of the new friction material.

Is this kit enough for 37-inch tires?

Owners on user forums who run this Z36 setup generally recommend it for 35-inch tires or smaller. Several said that 37-inch tires and heavier loads call for a larger big-brake system.

Installing it yourself

The manufacturer's front brake pad installation guide is written for a DIY job at home, but it still requires care around the hydraulic system. Check the brake fluid level before you start, since the brake fluid reservoir should be about half full. Never allow the caliper to hang from the brake hose, because this can damage the hose. Clean any rust from the hub mating surface with a wire brush, and install the new hardware, since worn or damaged hardware can lead to noise or poor brake pad performance. Torque the caliper bracket bolts to the manufacturer's specifications. Keep lubricant off the friction side of the pads. For full torque values and steps, refer to the vehicle's service manual.

  • MPN: CPK7940-36
  • Manufactured by: PowerStop
  • Units per SKU: 1
  • In Stock: 1, On Order: 1
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$275.82

MSRP / List price
Member Price
Your price after signing in
$275.82
Only 1 left in stock — order soon
Add to Cart:
MPN
CPK7940-36
Manufacturer
PowerStop
Availability
Only 1 left
Ships Same Day
Order before 5pm PST and this product ships same day
Member Pricing
Easy Returns
Expert Support
Secure Checkout