Free Shipping on Orders Over $99  ·  No Code Needed

Wilwood Caliper-Powerlite 1.38in Pistons .350in/.500in Disc

*Photo may not represent actual product

The Wilwood 120-8726 is a four-piston, radial-mount Powerlite caliper with a forged aluminum body and a Type III anodized finish. The process of stress-flow forging re-aligns the metal's grain structure within the contour of the caliper body. Its stainless pistons are 1.38-inch bore, giving 3.00 square inches of total piston area, and the manufacturer positions the caliper for sports, rally, and off-road builds. Owners on user forums tend to choose it when a lighter, heat-tolerant caliper is needed for a 0.500-inch rotor setup and the stock single-piston hardware is no longer adequate. The forged body avoids the grain-structure stress that machining a straight block billet can introduce, and the bridge plates are stainless steel. The manufacturer says these plates extend the service life of the caliper body by limiting bridge wear from pad gouging, which is a durability edge over a generic cast unit.

Fitment is straightforward for a universal mount, and four corner bleed screws assure simple and effective air evacuation from the system and allow one caliper to be mounted in any front, rear, right or left position. The pad radius matches to rotor diameters between 9.45" (240,0 mm) and 11.75" (298,5 mm), and the caliper is listed for 0.35 to 0.50 inch rotor width. For DIY installers, the Quick-clip pad retainers let you swap pads without caliper removal, which speeds up track-day pad changes. Searches for a 1.38 four-piston radial caliper, 5.08 radial mount Wilwood install, and 0.500 rotor rally caliper upgrade are the usual starting points for this part.

  • Caliper Type: Four-piston radial mount, universal side
  • Piston Bore: 1.38 in, stainless steel
  • Total Piston Area: 3.00 sq in
  • Mount Center: 5.08 in
  • Rotor Width: 0.35 in to 0.50 in
  • Rotor Diameter: 9.45 in to 11.00 in
  • Pad Type: 7912
  • Finish: Type III anodize
  • Inlet Thread: 1/8-27 NPT
  • Dust Boot: None

FAQ:

What rotor sizes does the 120-8726 fit?

The manufacturer lists a rotor width range of 0.35 to 0.50 inch and a rotor diameter range of 9.45 to 11.00 inches. The pad radius is designed for rotor diameters between 9.45 and 11.75 inches, so confirm your rotor thickness and hub offset before ordering.

Which rebuild parts are available for this caliper?

The manufacturer's ordering data lists piston part 200-8732 (1.38 in) and square ring kit 130-2658 (4-pack) for this caliper. Confirm the complete rebuild list with the manufacturer before ordering, since other components are listed in a table that is hard to read.

Can this caliper be used on either side of the vehicle?

Yes. The manufacturer lists the mount side as universal, and the four corner bleed screws let one caliper be used in any front, rear, left, or right position.

Installing it yourself

Wilwood's install guidance stresses that the work should be done by someone experienced with disc brake systems. Before torquing anything, initially place shims between the bracket and the upright, then check that the rotor is centered in the caliper through the top opening. Wilwood's assembly sheets for related radial kits call for red Loctite 271 on mounting bolts, and note that the bracket must sit squarely on the mount bosses. Use stainless safety wire where the sheet shows it. Check for at least 0.080 inch of clearance between the caliper and wheel in all areas. Confirm the torque values on the sheet for your specific bracket, because this listing does not confirm a single torque figure.

  • MPN: 120-8726
  • Manufactured by: Wilwood
  • Units per SKU: 1
  • In Stock: 7
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$197.43

MSRP / List price
Member Price
Your price after signing in
$197.43
In Stock — ships same day if ordered before 5pm PST
Add to Cart:
MPN
120-8726
Manufacturer
Wilwood
Availability
In Stock (7)
Ships Same Day
Order before 5pm PST and this product ships same day
Member Pricing
Easy Returns
Expert Support
Secure Checkout