Free Shipping on Orders Over $99  ·  No Code Needed

Borla 08-13 BMW M3 Coupe 4.0L 8cyl 6spd/7spd Aggressive ATAK Exhaust (rear section only)

*Photo may not represent actual product

The Borla 11802 is an ATAK axle-back replacement for the rear section of the factory exhaust, built for the high-revving S65 4.0L V8 in the 2008-2013 BMW M3 E92/ E93 4.0L V8 Automatic/ Manual Transmission Rear Wheel Drive 2 Door Coupe/ Convertible layout. The tubing and tips are high-quality lightweight T-304 austenitic stainless steel, with straight-through mufflers and dual split rear exits. Owners on user forums say the ATAK tuning delivers a muscular idle and a noticeably wider volume rise once throttle goes on, so it suits drivers who want the M3's exhaust note to be the main event. Owners on user forums also report the system is roughly 21 lbs lighter than stock, which matters at the rear of a car this size.

Choose this over the factory system if you want a bolder tone than the OEM setup and a rear section built for owners who have asked Borla about weight, sound, and performance. Owners on user forums describe the ATAK as quiet at low-load city driving but busy on longer highway runs, and a few report it is too loud for daily use. Cold-start volume is a common complaint, and at least one owner on user forums modified the ECU to reduce it. Searchers looking for an E92 M3 ATAK axle-back, E93 M3 rear section exhaust, S65 V8 straight-through muffler upgrade, or 11802 install will find this part matches those needs.

  • Manufacturer Part Number: 11802
  • System Type: ATAK axle-back (rear section) exhaust
  • Fitment: 2008-2013 BMW M3 E92 Coupe / E93 Convertible, 4.0L S65 V8, rear-wheel drive, automatic or manual transmission
  • Material: T-304 austenitic stainless steel, all-welded construction
  • Muffler Design: Straight-through
  • Exit Style: Dual split rear with polished 3.14" round T-304 stainless tips
  • Sound Level: Borla ATAK

FAQ:

Does this fit a 2008-2013 M3 sedan?

The manufacturer's product page lists the E92 coupe and E93 convertible, but the manufacturer's install sheet also references a 4-door sedan. Confirm fitment with the manufacturer before ordering.

Is the ATAK system loud on the highway or does it drone?

Details vary by driver and setup. Some owners on user forums say it has little drone at cruise, while others find it too busy at 70 mph on long drives.

Will the cold-start volume be a problem?

Owners on user forums report cold start is louder than the factory system. At least one owner reduced it by modifying the ECU software.

Can the ATAK system cause rattles?

One owner on user forums reported a new rattle near the e-brake area after installation. Check hanger and clamp alignment after fitting if you notice similar noise.

Installing it yourself

The manufacturer's install sheet for this rear section calls for a 3/8" drive ratchet, a 3" extension, 13mm and 15mm sockets, and a pry bar. The steps include unbolting the factory clamps behind the resonators, lubricating hangers and rubber isolators, removing the rear muffler isolators, and supporting the new section with a muffler stand or a helper. Reuse the factory clamps as the sheet directs, and remove the original ground straps and isolators before fitting. Borla's install sheet recommends an exhaust shop or professional installer, so plan accordingly if you are not comfortable working under the car. Owners on user forums say the fitment lines up well, though one reported weld alignment issues on an early unit that the manufacturer addressed.

  • MPN: 11802
  • Manufactured by: Borla
  • Units per SKU: 1
  • In Stock: 4
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$2,079.99

MSRP / List price
Member Price
Your price after signing in
$2,079.99
Only 4 left in stock — order soon
Add to Cart:
MPN
11802
Manufacturer
Borla
Availability
Only 4 left
Ships Same Day
Order before 5pm PST and this product ships same day
Member Pricing
Easy Returns
Expert Support
Secure Checkout