Free Shipping on Orders Over $99  ·  No Code Needed

Borla 08-12 Toyota Sequoia SR5/Platinum/Ltd 5.7L 8cyl AT 6spd RWD/4WD SS Catback Exhaust

*Photo may not represent actual product

Borla's 140277 is a Touring-tuned cat-back system for the 5.7L V8 Toyota Sequoia. It attaches behind the catalytic converter, unbolting the two flanges located just behind the catalytic converter to clear the factory pipe. Its two 2.25-inch inlets merge into a single 2.75-inch run that finishes in a 4-inch bright chrome tip. The tubing and tip are T-304 stainless, which the manufacturer states is superior to T-400 series knockoffs (such as 409).

The reason to spend money here instead of on stock or a budget muffler is the tone. The Touring tune is Borla's mildest option and is meant to deliver the mellow Touring sound with no drone inside the vehicle, which matters on long highway runs. The internal build also counts: ultra-smooth mandrel bends ensure maximum flow & power, and precision computer numerical control (CNC) manufacturing ensures an accurate fit. Buyers searching for a drone-free cat-back for a 2008 to 2020 Sequoia 5.7L, or a T-304 stainless Touring system for a 4WD Sequoia, are looking at this category.

Fitment is the first thing to verify. The manufacturer's install sheet says the part has been designed for the 2008-2020 Toyota Sequoia equipped with a 5.7L V8 engine and 2WD or 4WD automatic transmission. Its product page lists a wider range, 2008-2022 Toyota Sequoia 5.7L V8 Automatic Transmission 2 & 4WD, so confirm your model year with the manufacturer before ordering. For DIY work, the install sheet reuses the factory hangers and hardware, and the manufacturer recommends a 3/8-inch ratchet, 15mm socket, pry bar, and spray lubricant. A muffler stand or helper is essential, and the system should be torqued to the manufacturer's values rather than run with an impact gun.

  • Manufacturer Part Number: 140277
  • Exhaust Type: Cat-back system, Touring tune
  • Vehicle Application: Toyota Sequoia 5.7L V8, automatic transmission, 2WD/4WD (manufacturer install sheet covers 2008-2020; product page lists 2008-2022)
  • Inlet Diameter: Dual 2.25 in.
  • Tubing Diameter: 2.75 in. single outlet
  • Tip: 4 in. bright chrome, single round rolled angle-cut
  • Material: T-304 austenitic stainless steel

FAQ:

Which Sequoia model years does this exhaust fit?

The manufacturer's installation sheet for part 140277 specifies 2008-2020 Sequoia models with the 5.7L V8, while its product page lists 2008-2022. Confirm your model year directly with the manufacturer before ordering, especially for 2021 and 2022 vehicles.

Will the Touring system drone on the highway?

The manufacturer describes the Touring tune as drone-free inside the cabin. Individual experience can vary with engine speed and cabin layout, so the manufacturer is the best source for tuning questions.

Can I install it with an impact wrench?

No. The manufacturer's install instructions for Borla performance exhaust systems advise against using air impact tools on the fasteners, because they can cause bent flanges or gasket leaks. Torque each fastener to the manufacturer's values and follow its tightening sequence.

Installing it yourself

Per the manufacturer's install sheet for this part, the job is a bolt-on replacement that reuses the factory hanger locations. Expect the work to be a moderate DIY project: the sheet calls for a 3/8-inch ratchet, a 3-inch extension, a 15mm socket, a pry bar, and spray lubricant. Lubricate the hangers and rubber isolators before removal, and use a muffler stand or a second person to support the sections while the hangers come off. Place the new front muffler assembly onto the original hardware and set the hangers into the rubber isolators, then hand-tighten until alignment is checked. Leave the clamps loose until tip position is correct, then tighten to the manufacturer's torque values. Tip alignment on dual-outlet systems can take patience, so plan extra time for fine adjustment.

  • MPN: 140277
  • Manufactured by: Borla
  • Units per SKU: 1
  • In Stock: 3
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$1,499.99

MSRP / List price
Member Price
Your price after signing in
$1,499.99
Only 3 left in stock — order soon
Add to Cart:
MPN
140277
Manufacturer
Borla
Availability
Only 3 left
Ships Same Day
Order before 5pm PST and this product ships same day
Member Pricing
Easy Returns
Expert Support
Secure Checkout