Free Shipping on Orders Over $99  ·  No Code Needed

Fox Factory Race 2.0 x 4.0 Bump Stop 1-1/4in. Shaft 14.19 Ext 10.15 Comp Pinch Mount

*Photo may not represent actual product

The Fox Factory Race 2.0 x 4.0 Bump Stop (MPN 981-20-043) is a 2.0-inch-body bump stop with 4.04 inches of travel, built on Fox's Factory Race Series 2.0 platform. The manufacturer describes these stops as developed with off-road racing teams to control the last few inches of suspension travel. This pinch-mount version uses a 1-1/4-inch hard chrome plated 4130 chromoly shaft, a Cerakote-coated zinc-plated body, and black anodized CNC aluminum components. Compared with a stock rubber bump stop, it gives a more controlled landing near full compression and a replaceable Delrin strike pad that keeps contact quieter, which justifies the price for a serious long-travel or competition build.

Fitment depends on your mounting hardware more than on the vehicle itself. The pinch style needs a 2.0-inch pinch-bolt mounting can, and owners on user forums report that rear installs typically mean cutting the factory holder and welding the can in place, while some front setups use lock rings threaded onto the stock bump tube. Searching for a Fox 2.0 pinch bump stop, 4 inch travel bump stop install, or 2.0 x 4.0 bump stop 1-1/4 shaft will bring up the most relevant install guidance. Confirm clearance for the 14.19-inch extended and 10.15-inch compressed lengths before ordering.

  • Travel: 4.04 in
  • Extended Length: 14.19 in
  • Compressed Length: 10.15 in
  • Body Diameter: 2.0 in
  • Shaft Diameter: 1-1/4 in, hard chrome plated 4130 chromoly
  • Top Mount: Pinch (requires 2.0 in pinch-bolt mounting can)
  • Bottom Mount: None
  • Strike Pad: Replaceable Delrin
  • Body Finish: Cerakote ceramic coating over zinc plated basecoat
  • MPN: 981-20-043

FAQ:

Do I need to weld anything to install this bump stop?

Owners on user forums report that rear installs generally require cutting holes and welding the pinch can on, while some front applications use lock rings threaded onto the factory bump stop tube instead.

How is the engagement point set?

The manufacturer's install guidance for Fox bump stops describes moving the lock ring and threading the bump stop until the desired engagement location is reached, with full thread engagement on the bump stop.

Can I adjust the bump stop after it is installed?

Owners on user forums note that the height can be adjusted by repositioning the lock rings, so you can fine-tune when the stop engages during up-travel without re-welding.

Installing it yourself

This is an advanced fabrication-level install, not a bolt-on. Expect to lift and secure the vehicle, remove the wheels and coil springs (the manufacturer's guidance recommends a professional spring compressor), and remove the factory bump stop by pryng it from its holder. Required tools typically include a cut-off saw, a welder, a spanner wrench for the lock rings, and medium-strength thread-lock, which the manufacturer's install guidance recommends on all bolts. The manufacturer advises cutting the stock holder just above the weld, and warns against welding with the new bump stop already threaded in, since heat can damage it. Owners on user forums caution that brake lines and other components near the coil bucket may need to be moved first.

  • MPN: 981-20-043
  • Manufactured by: FOX
  • Units per SKU: 1
  • In Stock: 37
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$379.95

MSRP / List price
Member Price
Your price after signing in
$379.95
In Stock — ships same day if ordered before 5pm PST
Add to Cart:
MPN
981-20-043
Manufacturer
FOX
Availability
In Stock (37)
Ships Same Day
Order before 5pm PST and this product ships same day
Member Pricing
Easy Returns
Expert Support
Secure Checkout