Free Shipping on Orders Over $99  ·  No Code Needed

EBC 01-05 Acura EL (Canada) 1.7 GD Sport Rear Rotors

*Photo may not represent actual product

The EBC GD7128 is a rear sport rotor from the manufacturer's GD line, built around a wide-aperture slot pattern. Designed with wide aperture slots to allow cooling, GD Sport Rotors show much less brake fade. GD Series sport rotors are machined in the U.K. from R90-approved blanks, and all sport rotors are balanced and runout inspected before release.

Compared with a stock rear disc, the appeal is cooler running and cleaner pad contact on repeated hard stops, which matters on canyon runs, towing, or track days. The slots also help clear gas and debris from the pad face, so the friction surface stays more consistent. Each rotor gets a 100% run-out, metallurgy, and dimensional check, and the manufacturer applies a long-lasting corrosion-resistant finish to its GD series, which is a practical edge over bare iron blanks. For 2001-2005 Acura EL 1.7 rear rotor replacement, the manufacturer's catalogue lists GD7128 at 10.2 inches with FMSI D537 pad compatibility and DP21193 pads.

  • Position: Rear
  • Fitment: 2001-2005 Acura EL 1.7L (Canada listing)
  • Rotor diameter: 10.2 in (260 mm)
  • Pad reference: FMSI D537
  • Design: Solid, wide-aperture slotted sport rotor
  • Finish: Long-lasting corrosion-resistant coating
  • Manufacturer part number: GD7128

FAQ:

Do I need new pads when I install these rotors?

The manufacturer's install sheet says new pads must always be fitted after new rotors go on, because worn pads on new rotors can create hot spots that damage them. Rotors should always be replaced in pairs.

Is there a separate bedding-in procedure for these rotors?

No. The manufacturer notes that since new rotors must always be installed with new pads, it does not have a rotor-specific bedding-in procedure. Bed the new rotors by following the bedding-in procedure for the new pads.

What runout reading should I aim for after installation?

Per the manufacturer's install sheet, keep bumping the rotor to a new bolt position until the run-out reads less than 0.08mm.

Does GD7128 also fit other Acura models?

The manufacturer's catalogue lists the same part number for certain RSX and Integra Type-R applications as well as the 1.7L EL, so confirm fitment against your VIN before ordering.

Installing it yourself

Expect a standard rear brake job. The manufacturer's install sheet calls for a dial indicator for run-out measurement, a jack, axle stands and wheel chocks, the correct wheel nut socket, a torque wrench set to the vehicle manufacturer's wheel nut specification, and brake cleaner with a clean rag. Poor-condition wheel hubs are the number one cause of rotor run-out, so clean the hub face thoroughly. Mount the rotor with the wheel nuts snug, measure run-out, and if it is too high, remove the rotor, rotate it clockwise by one bolt position, and secure it again. After installation, avoid coming to a complete stop while the brakes are hot during bedding, and mechanical bedding typically takes about 50-100 km of normal road driving before full pad contact is established.

  • MPN: GD7128
  • Manufactured by: EBC
  • Units per SKU: 1
  • In Stock: 4
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$221.44

MSRP / List price
Member Price
Your price after signing in
$221.44
Only 4 left in stock — order soon
Add to Cart:
MPN
GD7128
Manufacturer
EBC
Availability
Only 4 left
Ships Same Day
Order before 5pm PST and this product ships same day
Member Pricing
Easy Returns
Expert Support
Secure Checkout