Free Shipping on Orders Over $99  ·  No Code Needed

Power Stop 97-01 Acura Integra Rear Z23 Evolution Sport Brake Kit

*Photo may not represent actual product

The PowerStop Z23 Evolution Sport Rear Brake Kit (K2270) is a complete rear-axle upgrade for the 1997-2001 Acura Integra. It bundles Z23 carbon-fiber reinforced ceramic pads, drilled and slotted rotors, and stainless-steel installation hardware. The manufacturer positions it as a bolt-on upgrade for daily drivers who want more stopping power than stock without a full brake overhaul. Its ceramic compound is built to resist fade under heat, and its low-dust, quiet pad formula keeps rear wheels cleaner than standard pads.

The main reason to choose this kit over a pad-only swap or a cheaper bargain set is that the pads, rotors, and hardware are sold as one matched package. The cross-drilled, slotted rotors vent gas, dust, and moisture from the pad surface, and the silver zinc dichromate plating is meant to resist rust on rear rotors exposed to road salt. The manufacturer calls break-in critical, so do not skip it. Its procedure calls for five moderate to aggressive stops from 40 mph to 10 mph, followed by five stops from 35 mph to 5 mph, then a cool-down drive. This lays an even friction layer on the rotors and helps prevent pedal judder.

Fitment is the first thing to verify. Fitment details for K2270 vary between sources, and the manufacturer's trim-by-trim confirmation was not located, so check your exact Integra trim and VIN before ordering. For a home mechanic, this is a bolt-on job that calls for a jack, jack stands, a C-clamp, DOT 3 or 4 brake fluid, and brake pad grease. Pair it with a bleed of the system and proper lug nut torque, and you have a rear brake upgrade searchable under terms like 1997-2001 Integra rear Z23 ceramic pads, drilled slotted rear rotors, and K2270 break-in procedure.

  • Manufacturer Part Number: K2270
  • Position: Rear
  • Vehicle Application: 1997-2001 Acura Integra (trim fitment varies by source; confirm before ordering)
  • Pad Compound: Z23 carbon-fiber reinforced ceramic
  • Rotor Style: Drilled and slotted
  • Rotor Finish: Silver zinc dichromate plating for rust resistance
  • Included Hardware: Premium stainless-steel hardware and pin bushing kit

FAQ:

Which Integra trims does the K2270 rear kit fit?

Fitment details for this kit vary between sources, and the manufacturer's trim-by-trim confirmation was not located during research. Confirm your exact trim and VIN with the manufacturer before ordering.

Does this kit need a break-in before normal driving?

Yes. The manufacturer's break-in procedure for drilled and slotted rotors calls for five moderate to aggressive stops from 40 mph to 10 mph without coming to a complete stop, then five stops from 35 mph to 5 mph, then a moderate-speed cool-down drive of about five minutes.

What hardware comes with the kit?

The manufacturer states the kit includes premium stainless-steel installation hardware and a pin bushing kit, so no separate hardware purchase should be needed for a standard install.

Installing it yourself

This is a bolt-on rear brake job that a home mechanic can handle with a jack, jack stands, a C-clamp, DOT 3 or 4 brake fluid, and brake pad grease. Block the wheels and set the parking brake before lifting, and loosen the lug nuts before jacking the car. The manufacturer's install sheet says the guide is for reference only, so follow your vehicle's factory service manual for specifics. Watch for two common gotchas: the rear caliper piston must be pushed back into the body to clear the thicker new pads, and the caliper's rubber boot can extend a bolt and cause interference during reassembly. If you are not replacing the rotor, the manufacturer suggests threading two lug nuts backwards through the rotor to hold it in place while the caliper is off. After reassembly, bleed the system, fill the reservoir only to the max line, and torque the lug nuts in sequence. Then complete the break-in, and do not cool the brakes with water.

  • MPN: K2270
  • Manufactured by: PowerStop
  • Units per SKU: 1
  • In Stock: 6, On Order: 1
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$128.22

MSRP / List price
Member Price
Your price after signing in
$128.22
In Stock — ships same day if ordered before 5pm PST
Add to Cart:
MPN
K2270
Manufacturer
PowerStop
Availability
In Stock (6)
Ships Same Day
Order before 5pm PST and this product ships same day
Member Pricing
Easy Returns
Expert Support
Secure Checkout