Free Shipping on Orders Over $99  ·  No Code Needed

Wilwood Caliper-MC4 Mechanical-L/H - Red w/ Logo 1.19in Piston .81in Disc

*Photo may not represent actual product

Wilwood's MC4 Mechanical Parking Brake Caliper is a stand-alone, multi-use, cable-operated brake caliper, so it works as a dedicated parking brake on a build that needs a separate mechanical unit. Its die-cast body is paired with a forged billet anvil, which the manufacturer says provides superior strength under load, yet is lightweight at only 3.30 (2.95 without pads) pounds. Each caliper ships with Wilwood's Composite Metallic (CM) high-friction, high static-hold brake pads, and are pre-fitted with noise cancelling shields. The high-gloss red powder coat is heat and brake-fluid resistant and carries Wilwood's logo.

The case for this caliper over a generic cable-pull unit is holding power and simple adjustment. The manufacturer describes high static-hold performance from its pad compound, and the manual adjuster lets you take up pad and rotor wear without special tools. The unit is a left-hand pull design with 4.75-inch mount holes and is built to accept rotors that are .810" thick, so it suits a Wilwood-style rear parking brake setup where the rotor width is known in advance.

Plan the install around the cable. The stock parking brake cable will not work, so you will need Wilwood's universal cable kit, sold separately, to connect the caliper. Cable routing should be kept as straight as possible, since bends reduce efficiency and pull force at the brake. Keep at least .080" clearance between the wheel and caliper in all areas, and center the rotor in the caliper before tightening. Pre-stretch the cables and re-adjust them before final setup.

  • Caliper Series: MC4 Mechanical Parking Brake
  • Actuation: Cable-operated mechanical lever
  • Mount Side / Pull: Left-hand pull
  • Mount Hole Spacing: 4.75 in
  • Rotor Thickness: 0.810 in (20.6 mm)
  • Pads: Composite Metallic (CM) high-friction, pre-fitted
  • Body Construction: Die-cast body with forged billet anvil
  • Weight: 3.30 lb (2.95 lb without pads)
  • Finish: Gloss red high-temp, brake-fluid-resistant powder coat with Wilwood logo
  • Adjustment: Manual, no special tools required

FAQ:

Can I reuse the factory parking brake cable with this caliper?

The manufacturer states that OEM parking brake cables will not work with Wilwood calipers. Wilwood's universal parking brake cable kit is the intended connection and is sold separately.

What rotor thickness does this caliper accept?

Per the manufacturer, the MC4 is built to accept rotors that are .810 inch thick.

Do I need special tools to adjust the parking brake?

Per the manufacturer, the manual adjuster requires no special tools and allows incremental adjustment for pad and rotor wear.

Installing it yourself

Per the manufacturer's install sheets, the caliper mounts to a steel bracket, and the rotor should be centered in the caliper, using shims if needed. The installer is responsible for routing the cable and ensuring it has adequate clearance and retention, so plan the cable route before final assembly. After setup, adjust the caliper until it drags lightly on the rotor, then cycle the lever until the adjustment stops tightening. Confirm the full holding power only after bleeding and bedding the brakes.

  • MPN: 120-12070-RD
  • Manufactured by: Wilwood
  • Units per SKU: 1
  • In Stock: 8
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$171.56

MSRP / List price
Member Price
Your price after signing in
$171.56
In Stock — ships same day if ordered before 5pm PST
Add to Cart:
MPN
120-12070-RD
Manufacturer
Wilwood
Availability
In Stock (8)
Ships Same Day
Order before 5pm PST and this product ships same day
Member Pricing
Easy Returns
Expert Support
Secure Checkout