Free Shipping on Orders Over $99  ·  No Code Needed

Power Stop 05-19 Chrysler 300 Rear Z23 Evolution Sport Brake Kit

*Photo may not represent actual product

The Power Stop K1720 is a rear kit from the Z23 Evolution Sport line, built around carbon-fiber ceramic pads that the manufacturer positions as an upgrade over stock pads for reducing brake dust. The kit pairs those pads with matched rotors, so a rear brake job on a Chrysler 300 can be handled as one system rather than mixing parts from different lines. The real value over a cheaper generic pad is the break-in process: the manufacturer stresses controlled bedding stops so an even friction layer transfers to the rotors, and skipping that step is the most common way buyers lose the braking performance they paid for. Searching for a Z23 Evolution Sport rear kit for a 300, a carbon ceramic rear brake upgrade, or low-dust Chrysler 300 rear pads and rotors will bring up this part.

Fitment is listed for the 2005 to 2019 Chrysler 300, but other listings show later model years, so confirm your VIN with the manufacturer before ordering. The job is a practical driveway project for a mechanically confident owner. You will block the front wheels, break loose the lug nuts, support the car on jack stands set on level ground, remove the caliper bracket, swap the rotor, and reset the rear caliper piston before installing the new pads. The manufacturer's guidance calls for DOT 3 or 4 brake fluid, brake pad grease, and a C-clamp, and it advises against a torque gun for final lug tightening.

  • Position: Rear axle
  • Pad compound: Z23 Evolution Sport carbon-fiber ceramic
  • Vehicle fitment: 2005-2019 Chrysler 300 (confirm years with the manufacturer or your VIN)
  • Manufacturer part number: K1720
  • Break-in: Five moderate-to-aggressive stops from 40 mph to 10 mph, five moderate stops from 35 mph to 5 mph, then a cooling drive

FAQ:

How should I break in the Z23 Evolution Sport pads on this kit?

The manufacturer's procedure calls for five moderate-to-aggressive stops from 40 mph down to 10 mph without letting the brakes cool and without coming to a complete stop. Follow that with five moderate stops from 35 mph to 5 mph, then drive for about five minutes at moderate speed without heating the brakes excessively. Once the brakes reach normal operating temperature, use them normally. The manufacturer also advises never cooling the brakes with water.

Why does the bedding process matter for a rear kit?

According to the manufacturer, proper bedding establishes an even layer of friction material on the rotors. The manufacturer's installation guide warns that skipping or rushing the break-in can cause brake pedal pulsation and thermal stress cracks in the rotor.

Installing it yourself

Plan on a moderate DIY job for someone comfortable working under a car. Gather a floor jack, jack stands, wheel chocks, a C-clamp, a torque wrench, brake pad grease, and fresh DOT 3 or 4 fluid in case the caliper piston must be pushed back and the brake line is opened. Keep the caliper hanging by its hose only briefly, because the manufacturer's install approach avoids letting it dangle from the line. Check the hub mounting surface for rust and clean it before fitting the new rotor. Rear caliper pistons on many vehicles screw in and out instead of retracting straight back, so check how yours moves before forcing it with a clamp. Finish by torquing the lug nuts to the manufacturer's specification in an alternating pattern after lowering the car.

  • MPN: K1720
  • Manufactured by: PowerStop
  • Units per SKU: 1
  • In Stock: 4
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$229.09

MSRP / List price
Member Price
Your price after signing in
$229.09
Only 4 left in stock — order soon
Add to Cart:
MPN
K1720
Manufacturer
PowerStop
Availability
Only 4 left
Ships Same Day
Order before 5pm PST and this product ships same day
Member Pricing
Easy Returns
Expert Support
Secure Checkout