Free Shipping on Orders Over $99  ·  No Code Needed

Power Stop 00-05 Ford Excursion Rear Red Calipers w/Brackets - Pair

*Photo may not represent actual product

The Power Stop S4752 is a pair of rear brake calipers sold with mounting brackets, built as a bolt-in replacement for the Ford Excursion and 2000-2004 F-250/F-350 Super Duty. PowerStop Powder Coated Brake Calipers are made specifically with the enthusiast in mind. The calipers and brackets are remanufactured in Chicago, IL and treated with an electrostatic high-temperature red powder-coating. For buyers weighing a cheaper unbranded caliper, the value is in the rebuild: each caliper is 100% pressure tested to verify piston operation. They are assembled with new seals, caliper slide pins and bolts, dust boots, bleeder screws, and stainless-steel pad attachment hardware. Owners on user forums who paired them with new pads, rotors, and braided lines report zero problems and very little brake dust.

Fitment is listed for 2000-2005 Excursion and 2000-2004 F-350 and F-250 Super Duty applications. Early 2000 Excursions are a special case: the very early build date EXs did indeed have different rear caliper orientation vs the later build wagons, so confirm your build date and bleeder placement before ordering. The swap itself is a typical rear caliper job. Owners describe 2 caliper mounting bolts and 2 slide bolts and advise supporting the caliper rather than letting it hang by the hose. Searches for bolt-on rear brake caliper upgrade, red powder-coated Excursion calipers, and F-250 Super Duty rear calipers pair match this application.

  • Fitment: 2000-2005 Ford Excursion; 2000-2004 Ford F-250 and F-350 Super Duty
  • Position: Rear (sold as a pair with brackets)
  • Caliper Body: Cast iron
  • Caliper Type: Floating, 2-piston
  • Finish: Electrostatic high-temperature red powder coat
  • Condition: Remanufactured
  • Included: Bleeder screws, new seals, dust boots, slide pins

FAQ:

Do these fit every 2000 Excursion, or does build date matter?

User forums report that early-build 2000 Excursions used a different driver-side rear caliper orientation than later builds, and one owner found that a mismatched caliper put the bleeder on the bottom. Check your build date and confirm the correct caliper with the manufacturer before installing.

Are these new or remanufactured calipers?

The manufacturer describes them as remanufactured at its Chicago, Illinois facility, with new seals, pins, and dust boots installed during assembly.

Installing it yourself

This is a moderate rear brake job that a home mechanic with jack stands and a torque wrench can handle. Owners recommend loosening the caliper mounting bolts before removing the slide bolts, then supporting the caliper once the bolts are out. One owner's write-up lists torque values of 166 ft-lbs for the mounting bolts and 42 ft-lbs for the slide bolts, so verify those against a service manual. When removing slide pins, keep them in order, since one has a notch that must face the top of the caliper. Rear rotors can be stuck, and one owner needed a slide hammer to free them. Bleed the brakes after installation and confirm the bleeder is at the top.

  • MPN: S4752
  • Manufactured by: PowerStop
  • Units per SKU: 1
  • In Stock: 5
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$261.83

MSRP / List price
Member Price
Your price after signing in
$261.83
Only 5 left in stock — order soon
Add to Cart:
MPN
S4752
Manufacturer
PowerStop
Availability
Only 5 left
Ships Same Day
Order before 5pm PST and this product ships same day
Member Pricing
Easy Returns
Expert Support
Secure Checkout