Free Shipping on Orders Over $99  ·  No Code Needed

BAK 14-19 GMC/Chevrolet Silverado/Sierra 5ft 9in Bed BAKFlip MX4 EZ-Lift

*Photo may not represent actual product

The BAK 450120 is a hard-folding tonneau cover from the BAKFlip MX4 EZ-Lift line, sized for the 5'9" bed on 2014–2019 Chevrolet Silverado 1500 and GMC Sierra 1500 trucks. The panels use ultra-strong aluminum over high-density polymer cores, and assisted panels plus a large paddle release let you open the lid with one hand, even with gloves on (spring/torsion-assisted panels, oversized paddle latch, and exclusive Flip Assist system). Compared with stock or a basic soft roll-up, the hard-fold design uses integrated perimeter seals and new tight-fit clamps to keep water out, and folding it toward the cab opens the full bed for oversized cargo. The panels also clear the third brake light and integrated camera in every position.

Fitment and install are both worth checking before you order. The manufacturer's description lists 2014-2018 (2019 Legacy/Limited) Chevy Silverado/GMC Sierra 5' 9" Bed, so verify your trim if you own a 2019. The cover mounts with clamps rather than fasteners through the bed, and the manufacturer describes a simple bolt-on process using the included tight-fit clamps. Searches for BAKFlip MX4 EZ-Lift 450120, 5.9 ft hard fold tonneau, and clamp-on Silverado 1500 tonneau installation will find this exact cover.

  • Cover Type: Hard folding tonneau cover (EZ-Lift)
  • Bed Length: 5'9" bed
  • Fitment: 2014–2018 Chevrolet Silverado 1500 and GMC Sierra 1500; 2019 coverage per manufacturer is Legacy/Limited trims only (confirm before ordering)
  • Panel Construction: Aluminum panels over high-density polymer core
  • Latch/Operation: Oversized paddle latch with Flip Assist and auto-latch
  • Mounting: Clamp-on, tight-fit clamps and hardware included
  • Origin: Assembled in the USA

FAQ:

Does the BAKFlip MX4 EZ-Lift require drilling into my bed?

The manufacturer describes a clamp-based installation with no cutting, trimming, or drilling required. Its install sheet, however, lists a 5/8" drill bit among the tools, so check the instructions included with your kit before starting.

Will this cover block my third brake light or backup camera?

The manufacturer states the MX4 design does not block the third brake light or an integrated camera in any panel position.

When are the spacer shims needed?

The manufacturer's install sheet says spacer shims are included with the rails to adjust how snugly the cover fits between the rail openings. It recommends fitting them to the clamping surface when mounting against a plain painted rail or spray-on liner.

Installing it yourself

The manufacturer's install guidance is designed for a DIY install that typically takes one person a few hours, though it benefits from a helper when setting the cover. Gather scissors or a utility knife, isopropyl alcohol, a 1/2" wrench or socket, a Phillips screwdriver, and a 5/8" drill bit with a drill, since the tool list in the manufacturer's sheet includes them. Clean the bulkhead and rail with soap and water, then wipe with isopropyl alcohol to remove wax and grease before applying the seal. Set the front clamp about 6 to 9 inches back, keep the rail square to the bed rail, and tighten each clamp until snug, then add roughly a half turn (about 10 ft-lbs) per the manufacturer's sheet. Under- or over-tightening can cause product failure, so follow the torque guidance closely.

  • MPN: 450120
  • Manufactured by: BAK
  • Units per SKU: 1
  • In Stock: 9, On Order: 10
Exclusive member pricing Free membership — sign in to see your price
Join Free →

$1,399.99

MSRP / List price
Member Price
Your price after signing in
$1,399.99
In Stock — ships same day if ordered before 5pm PST
Add to Cart:
MPN
450120
Manufacturer
BAK
Availability
In Stock (9)
Ships Same Day
Order before 5pm PST and this product ships same day
Member Pricing
Easy Returns
Expert Support
Secure Checkout